To get started with srsENB you will require a PC with a GNU/Linux based operating system and an SDR RF front-end. An SDR RF front-end is a generic radio device such as the Ettus Research USRP that connects to your PC and supports transmission and reception of raw radio signals.
If you are using Ubuntu operating system, you can install srsENB from the binary packages provided:
sudo add-apt-repository ppa:srslte/releases sudo apt-get update sudo apt-get install srsenb
If you are using a different distribution, you can install from source using the guide provided in the project’s GitHub page.
After installing the software you can install the configuration files into the default location (
~/.config/srsran), by running:
Running the software¶
To run srsENB with default parameters, run
sudo srsenb on the command line. srsENB needs to run with sudo admin privileges in order to be able to create high-priority threads. Upon starting, srsENB will attempt to find your RF front-end device, attempt to attach to the core network (EPC) and start broadcasting.
Example console output:
linux; GNU C++ version 6.3.0 20170618; Boost_106200; UHD_003.009.007-release Built in RelWithDebInfo mode using commit 6b2961fce on branch next. --- Software Radio Systems LTE eNodeB --- Reading configuration file /conf/enb.conf... Setting number of control symbols to 3 for 25 PRB cell. Opening USRP with args: type=b200,master_clock_rate=30.72e6 Setting frequency: DL=2630.0 Mhz, UL=2510.0 MHz Setting Sampling frequency 5.76 MHz Enter t to stop trace. ==== eNodeB started ===
Upon receiving a UE connection:
RACH: tti=3381, preamble=3, offset=1, temp_crnti=0x46 User 0x46 connected
With the eNodeB running and one or more UEs connected, type
t in the console to enable the metrics trace. Example metrics trace:
------DL------------------------------UL---------------------------------- rnti cqi ri mcs brate bler snr phr mcs brate bler bsr 46 14.1 2.0 25.1 28.4M 0.8% 24.8 0.0 23.1 9.60M 2.2% 140k 46 14.8 2.0 26.6 30.7M 0% 24.9 0.0 23.2 9.92M 0% 140k 46 14.7 2.0 26.3 30.1M 0.8% 24.9 0.0 23.1 9.90M 0% 140k 46 14.8 2.0 26.5 30.6M 0% 24.9 0.0 23.1 9.90M 0% 140k 46 15.0 2.0 26.7 30.9M 0% 24.8 0.0 23.1 9.83M 0% 140k 46 14.5 2.0 26.1 30.0M 0% 24.9 0.0 23.1 9.88M 0% 140k 46 14.8 2.0 26.3 30.3M 0% 24.8 0.0 23.1 9.84M 0% 140k 46 14.7 2.0 26.4 30.4M 0% 24.9 0.0 23.1 9.89M 0% 140k 46 14.7 2.0 26.4 30.4M 0% 24.9 0.0 23.2 9.91M 0% 140k 46 14.7 2.0 26.3 30.4M 0% 24.9 0.0 23.1 9.87M 0% 140k 46 14.8 2.0 26.4 30.4M 0% 24.9 0.0 23.1 9.88M 0% 140k
The eNodeb can be configured through the configuration file:
enb.conf. This configuration file provides parameters relating to the cell configuration, operating frequencies, transmit power levels, logging levels and much more. To run srsENB with the installed configuration file, use
sudo srsenb ~/.config/srsran/enb.conf.
All parameters specified in the configuration file can also be overwritten on the command line. For example, to run the eNodeB with a different EARFCN, use
sudo srsenb ~/.config/srsran/enb.conf --rf.dl_earfcn 3350.
In addition to the top-level configuration file, srsENB uses separate files to configure SIBs (sib.conf), radio resources (rr.conf) and data bearers (drb.conf). These additional configuration files are listed under [enb_files] in the top-level enb.conf and defaults are provided for each.
A key eNodeB parameter is enb.mme_addr, which specifies the IP address of the core network MME. The default configuration assumes that srsEPC is running on the same machine. For more information, as well instructions for using an EPC on a separate machine, see the EPC user manual.
To use srsENB to create an over-the-air local cell, you will need an RF front-end and suitable antennas. The default EARFCN is 3400 (2565MHz uplink, 2685MHz downlink). To reduce TX-RX crosstalk, we recommend orienting TX and RX antennas at a 90 degree angle to each other.
The srsENB can also be used over a cabled connection. The cable configuration and required RF components will depend upon your RF front-end. For RF front-ends such as the USRP, connect TX to RX and ensure at least 30dB of attenuation to avoid damage to your devices. For more detailed information about cabled connections, see Advanced Usage.
Operating System Setup¶
The srsENB runs in user-space with standard linux kernels. For best performance, we recommend disabling CPU frequency scaling. To disable frequency scaling use:
for f in /sys/devices/system/cpu/cpu[0-9]*/cpufreq/scaling_governor ; do echo performance > $f done
To observe srsENB results, use the generated log files and packet captures.
Log files are created by default at /tmp/enb.log. The srsENB configuration file can be used to specify log levels for each layer of the network stack and to enable hex message output. Supported log levels are debug, info, warning, error and none.
Log messages take the following format:
Timestamp [Layer ] Level Content
17:52:25.246 [RLC ] Info DRB1 Tx SDU
or with hex message output enabled:
17:52:25.246 [RLC ] Info DRB1 Tx SDU 0000: 8b 45 00 00 c7 f3 8b 40 00 01 11 d1 f6 c0 a8 03 0010: 01 ef ff ff fa 92 55 07 6c 00 b3 ee 41 4d 2d 53
PHY-layer log messages have additional details:
Timestamp [Layer] Level [Subframe] Channel: Content
17:52:26.094 [PHY1] Info  PDSCH: l_crb= 1, harq=0, snr=22.1 dB, CW0: tbs=55, mcs=22, rv=0, crc=OK, it=1, dec_time= 12 us
See the explanation here on setting up wireshark to decdode the pcaps captured by srsENB.